BVPWG - ZYTEL NYLON RESINS, BKB249

Product Identification

Product ID:ZYTEL NYLON RESINS, BKB249
MSDS Date:12/03/1992
FSC:9390
NIIN:00N053484
MSDS Number: BVPWG

Responsible Party
E I DUPONT DE NEMOURS & CO
1007 MARKET ST
WILMINGTON, DE 19898
US

Emergency Phone: 800-441-3637; 800-441-9300

Info Phone: 800-441-7515

Preparer: D.L. LICZWEK

Cage: 0ERJ7

Contractor
E.I. DUPONT DE NEMOURS & CO
WILMINGTON, DE 19898 US

Telephone: 800-441-7515;800-441-9442

Cage: 18873

Ingredients

POLYHEXAMETHYLENE DODECANDIAMIDE

CAS: 26098-55-5

OSHA PEL N/K

ACGIH TLV: N/K


LUBRICANTS

OSHA PEL N/K

ACGIH TLV: N/K


STABILIZERS

OSHA PEL N/K

ACGIH TLV: N/K


SOME GRADES MAY CONTAIN INGS 5, 6, 7, OR 8 PIGMENTS

RTECS: 9999999ZZ

OSHA PEL N/K

ACGIH TLV: N/K


BARIUM (SARA III)

CAS: 7440-39-3

RTECS: CQ8370000

Fraction By Weight: <2%

OSHA PEL 0.5 MG/M3

ACGIH TLV: N/K


COBALT (SARA III)

CAS: 7440-48-4

RTECS: GF8750000

Fraction By Weight: <2%

OSHA PEL 0.05 MG/M3

ACGIH TLV: 0.05 MG/M3, DUST


NICKEL (SARA III)

CAS: 7440-02-0

RTECS: QR5950000

Fraction By Weight: <2.5%

OSHA PEL 1 MG/M3

ACGIH TLV: 1 MG/M3


ZINC (SARA III)

CAS: 7440-66-6

RTECS: ZG8600000

Fraction By Weight: <2%

OSHA PEL N/K

ACGIH TLV: N/K

EPA Report Quantity: 1000 LBS

DOT Report Quantity: 1000 LBS

Hazards

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INGESTION: NOT A PROBABLE ROUTE
OF EXPOSURE. SKIN: MOLTEN POLYMER CAUSES THERMAL BURNS. EYES:
MECHANICAL IRRITATION ONLY. INHALATION: GRANULES NOT RESPIRABLE.
FUMES FROM OVERHEATING MAY CAUSE S YMPTOMS . CHRONIC EFFECTS: NONE
KNOWN.
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE KNOWN.

First Aid

First Aid:INHAL: IF EXPOSED TO FUMES FROM OVERHEATING, MOVE TO FRESH
AIR. CONSULT MD IF SYMPTOMS PERSIST. SKIN: WASH WITH SOAP & PLENTY
OF WATER. EYES: FLUSH EYES WITH WATER FOR AT LEAST 15 MINUTES.
CONSULT MD IF SYMPTOMS PERSIST. SKIN: IF MOLTEN POLYMER CONTACTS
SKIN, COOL RAPIDLY WITH COLD WATER. DO NOT ATTEMPT TO PEEL POLYMER
FROM SKIN. OBTAIN MEDICAL ATTENTION FOR THERMAL BURN.

Fire Fighting

Flash Point:752F,400C
Extinguishing Media:WATER, CARBON DIOXIDE, FOAM, DRY CHEMICAL.
Fire Fighting Procedures:USE NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:LARGE MOLTEN MASSES MAY IGNITE
SPONTANEOUSLY IN AIR. WATER QUENCHING OF SUCH MASSES IS GOOD
PRACTICE.

Accidental Release

Spill Release Procedures:SWEEP UP TO PREVENT A SLIPPING HAZARD.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling

Handling and Storage Precautions:COOL, DRY PLACE. KEEP CONTAINERS
TIGHTLY CLOSED TO PREVENT MOISTURE ABSORPTION AND CONTAMINATION.
Other Precautions:READ SECTION 12, SAFETY, IN "ZYTEL MOLDING GUIDE"
BULLETIN E-97221, BEFORE USING PRODUCT. FACE MASK & PROTECTIVE
CLOTHES RECOMMENDED FOR ABNORMAL PROCESSING PROBLEMS.

Exposure Controls

Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATOR APPROPRIATE
FOR EXPOSURE OF CONCERN . NONE UNDER NORMAL PROCESSING IF
VENTILATION IS ADEQUATE.
Ventilation:LOCAL EXHAUST AT PROCESSING EQUIPMENT TO KEEP PARTICULATE
BELOW 15 MG/M3 (OSHA LIMIT FOR NUISANCE DUSTS).
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPRVD CHEM WORKER GOGGLES .
Other Protective Equipment:LONG SLEEVE COTTON SHIRT & LONG PANTS IF
HANDLING MOLTEN POLYMER.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
NONE SPECIFIED BY MANUFACTURER.

Chemical Properties

Melt/Freeze Pt:M.P/F.P Text:>406F,>208C
Solubility in Water:INSOLUBLE
Appearance and Odor:GRANULES; NO ODOR.
Percent Volatiles by Volume:1

Stability

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND OXIDIZING AGENTS.
Stability Condition to Avoid:HEATING ABOVE 340C.
Hazardous Decomposition Products:COMBUSTION PRODS PRIMARILY AMMONIA,
CARBON MONOXIDE, SMALL AMOUNT OF HYDROGEN CYANIDE, ALDEHYDES.

Disposal

Waste Disposal Methods:LANDFILL OR INCINERATION IN COMPLIANCE WITH
FEDERAL, STATE AND LOCAL REGULATIONS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.